Plumbing, Heating and Pool Repair Guides

Beckett Replacement Oil Burner Pump

/
/
/
1127 Views

The Beckett Replacement Oil Burner Pump comes with pd timer to easily add pre-purge to non-prepurge controls. If your oil pump has failed or needs to be replaced you can rest easy knowing that the Beckett Burner Corp has a replacement waiting for you. Oil pumps can break due to age or possibly because of mechanical failure inside of the pump. The Beckett Oil Pump is a single stage pump with an integrated solenoid valve. You can have an oil burner technician come out to your house or place of business and replace the Beckett oil burner pump for you. This replacement oil pump for the Beckett Burner costs around $68.00.

Beckett 2184404GU Oil Burner Pump

Although extremely dependable oil burners, there is always the possibility that something can go wrong. Should there be any performance issues or otherwise with the burner, then check that there is power being supplied using a volt meter. Power surges are quite common and all it takes is to replace the fuse – it may look alright, but you had best check it with a meter just to be sure.

Once you can be sure that the power is working, and then check that the controls are all in working order. On the grey box on your Beckett pump, press the red button – this is the Protectorelay reset – and this should start the motor. If not, there could be a power outage with the motor.

A mistake that is quite often made is to not buy more oil. Running out of oil for heating happens a lot, but do not fret, as it is easily remedied. You need a container which is capable of holding flammable liquid, and make sure it can hold up to 5 gallons of liquids. Locate the nearest store which sells regular diesel or kerosene – not gas, but regular, you never use gas in your oil burner. Now you just have to filter the liquid in, let it settle for about ten minutes, then try and use the burner. This should be your fuel problems sorted!

Another common problem with an oil burner motor is that it stops spinning, and thankfully, this is not quite so difficult to fix as a pump replacement!

All you need to do is;

  • The oil burner is the round, black object on the right hand side of the burner. There are two screws that hold the motor on, so you need to need to remove both of these screws from the main burner body. Check for cracks afterward to ensure everything came off properly.
  • Unhook all the wires on the motor, make a note of where you unhooked the wires. Loosen the screws on the fan and remove the screw, and you can reinstall the motor when everything is fixed.
  • Install the fan onto your replacement motor. Put the couplings back in – be careful with this, it’s easy to get it wrong – and tighten the screws on the motor, and then test the fan to make sure it is not sticking. Sometimes it can be too tight with the screws and this can cause problems.
  • Hook up the wires according to your notes, and then once finished up – replace the protectorelay on the junction box if you have to – and you can turn on the oil burner and that should be you!

Remember that everything has to be handled with safety, especially wires and any of the parts – you do not want to have to hunt for a spare part all across the internet! However, with safety and care, all you need to do now is make sure that your pump does not break! If it does though, you can get in contact with us for an instant estimate.

15 Comments

  1. I have changed over to natural gas……..have 100 gals. in oil tank(feeds from top). is it possible to use pump on beckett burner to draw down supply into 5 gal. can ? I know it would be slow. thanks

  2. Maǥnificent website. A lot of usefսl information here.
    Ӏ’m sendingg it to some pals ans also sharikng in delicious.

    And of course, thanks tо your effort!

  3. I like the helpful information you provide for your
    articles. I will bookmark your blog and test again here regularly.
    I’m fairly sure I will be informed many new stuff proper here!
    Best of luck for the following!

  4. Just want to say your article is as astounding.
    The clearness for your post is just great and that i could think you’re a professional on this subject.
    Fine along with your permission let me to
    grab your feed to stay updated with imminent post. Thanks a million and
    please continue the gratifying work.

  5. You actually make it seem really easy with your presentation however
    I find this matter to be really one thing that I think I’d never understand.
    It seems too complicated and very huge for me. I am taking
    a look ahead for your subsequent publish,
    I’ll attempt to get the grasp of it!

  6. Hello there, You’ve done an incredible job. I’ll definitely digg it and personally suggest to my
    friends. I am confident they will be benefited from this web site.

  7. It’s truly very complicated in this active life to listen news on Television, thus I only use web for that reason, and get the latest information.

Leave a Comment

Your email address will not be published.

This div height required for enabling the sticky sidebar
Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views :