Plumbing, Heating and Pool Repair Guides

Hayward Perflex D.E Filter Repair & Troubleshooting

/
/
/
12823 Views

Hayward Swimming Pool Products makes a D.E. pool filter called the Perflex EC-Series Swimming Pool Filter. They make a few different sizes of this Perflex pool filter. The different names of the EC filters are the EC-30, The EC-40, The EC-50 and The EC-65, which is the largest model of the EC-SERIES line.Hayward Perflex D.E Filter Repair & Troubleshooting

You will find the Perflex EC-30/40 on many above ground swimming pools. You will find the larger models of the Perflex(EC-50/65), on many in-ground swimming pools. You will also find some EC-50/65 Perflex models can also be used on large above ground swimming pools. The Hayward Perflex EC40 swimming pool filter and other models of this Hayward pool filter have been installed into many backyards over the last 25 years and many will soon need repair or currently do. There are three different models of this filter but rebuilding and troubleshooting them is all basically the same as they all use commonly designed parts.

Many of the things that break on these types of swimming pool filters are actually caused by overuse or neglected repair to the pool filter. Some parts will just have to be replaced because of old age or just normal weathering. Hayward makes many replacement parts for the EC Perflex filter line so there is no need to worry about finding or buying replacement parts. You will only need a few common tools to be able to take apart and fully rebuild or repair your EC30, EC40, EC50 or EC65 swimming pool filter. You will need a basic standard socket set, a flathead screw driver, an open-end crescent wrench and a garden hose to wash the filter. You will also need some Teflon sealant tape to wrap around a few fittings and threads. If you have any broken fittings in your filter, you then will also need a small hammer.
Hayward Perflex DE Filter
If you know what part is already broken on your filter then you can just use this guide to repair the problem with your Perflex pool filter. If you have no idea what is wrong with the filter you can use the Hayward Perflex troubleshooting guide on the bottom of this page to help you figure out what parts you need to change. You will also always want to clean all the parts pf the swimming pool filter as you are working with them. There is no reason to work on a filter that caked up with dirty D.E powder. Always work safe and clean when working on your pool filter.

Most Common Hayward Perflex Pool Filter Problems w/Solutions:

Below you will find many common problems with easy to read DIY Pool Repair guides for the Hayward Perflex EC-Series filter. Most of these repairs can be done by the average person with a small set of tools. If you feel you can not do the repairs yourself for any reason, you can always call a swimming pool service professional to repair the problem for you. You can also bring your filter to many swimming pool repair centers to have them fix it for you.

How To Replace A Broken Hayward EC Pool Filter Gauge:

If your filter gauge on your filter is broken or cracked then you will need to replace it with a new one. Replacing the gauge on the EC40 or another EC Perflex filter requires just a few steps.

The first thing you will want to do is to buy a new replacement gauge for the Hayward EC filter that you are working on. Once you have the new gauge you can remove the gauge one of two different ways. The first way is to carefully grab the gauge with your hands and spin the gauge counter clockwise until it’s all the way out. If the gauge is tightened a lot you will have to use the other method to remove the gauge. This method would be to use an open-end wrench or a crescent wrench to remove the gauge from the filter.

Just on top of the gauge threads you will see a square that is made from the brass that the threads are. You can attach your wrench to that square and then turn the gauge counter clockwise to remove it. Once the gauge is removed you will want to install the new EC filter gauge. Before you screw the new gauge into the filter you will want to wrap the filter gauge threads a few times with some Teflon tape so that the gauge doesn’t leak. Once you wrap the Hayward EC swimming pool filter gauge a few times with the tape you can screw it back into the pool filter. Once you have hand tightened the filter gauge back into the filter you can use your wrench that you removed the gauge with to tighten the gauge all the way. Be sure to be careful as the gauge stem is made from brass and the filter is made from plastic. If you over tighten the gauge you cab crack the filter housing.
Hayward Perflex Extended Cycle DE Filter EC Series Parts Diagram Cutaway

How To Repair The Hayward EC-Series Pool Filter Bump Handle:

What makes the Hayward EC-series filter so unique is the way it works with the “bump handle” or D.E. media regeneration handle. This handle is used to regenerate the D.E. filter media as well as to shake off all of the D.E. from the fingers when its time to backwash. Sometimes this bump handle will break off from old age or when someone forces the handle down too fast when using it. When this happens you will need to replace the EC series bump handle with a new one.

In order to replace the bump handle on the Hayward EC65 or other sizes is to first remove the bump handle grip. This is the grip that is at the end of the handle itself. If you have a yellow tank EC filter you will just pull off the grip, as it is probably a runner one. If you have a new Hayward EC pool filter you will have a black hard plastic grip that will have a push tab at the end of it that you will have to push over. Once you push over the tab you will pull the grip off of the bump handle and then you can slide it on to your replacement Hayward EC filter bump handle.

Now that you have replaced the grip on the handle you will want to remove the cracked or broken handle from your Hayward Swimming Pool Filter. To do so you will have to remove to nuts and bolts that go through this handle. One bolt will go through the plastic top of the filter and this bolt is found at the end of the handle. The other bolt will go through the bump handle and the tube sheet bump shaft; this bolt will be at the center of the handle. You can remove both bolts with a Flathead screw driver and an open-end crescent wrench.

Once you have removed the two bolts you can remove the handle from the top of the Hayward Perflex Pool Filter tank. Now you will want to replace the handle with the new bump handle. To do so align the holes on the bump handle with the holes at on the filter tank and then push the bolt through. Once the bolt is through tighten down the nut clockwise a few turns. Once you have the first bolt in you will want to insert the second bolt through the bump handle and then through the bump shaft. Once the bolt is through you can fully tighten down both bolts and your new handle install will be complete.

How To Replace Cracked Tube Sheets:

If you look inside of the EC-series line of swimming pool filters from Hayward is something called “Tube Sheets” and something else called “filter fingers”. The tube sheets are pieces of round plastic that have many holes inside of them to hold the filter fingers. There are two different tube sheets inside of the filter. There is a top tube sheet and a bottom tube sheet. Often these tube sheets crack from pushing on the bump handle to hard. When the tube sheets crack they will allow D.E. powder back into the pool when running.

To replace the tube sheets you will have to remove all of the bolts hold the top of the EC tank lid to the body of the filter. In older models you will find lots of bolts that hold on he top and in new EC-40, 50 and 65 models you will find a single bolt that is connected to collar that holds the filter together. Once you remove the top of the filter you will be able to take off the top and see the fingers and tube sheets.

Now that you have the top off you will want to remove the center bolt from the bump handle that is connected through the stainless bump shaft that also goes through the tube sheets. Once you remove this though bolt you can pull the tube sheets and fingers from the filter top. You will now want to start removing all the small 5/16 bolts around the edges of the tube sheets and once you do the top tube sheet will separate from the bottom.

Once you do this you will have to remove two c-clips. One from the bottom of the tube sheet and one from t he top. It is easier to do the one on the top first and then you can slide the shaft through the tube sheets and remove the other one. It is always best to replace the c-clips in the perflex when you are changing the tube sheets.

When you remove the top tube sheet you will also have to be careful that you do not loose or damage the rubber tube sheet tank gasket. You will have to re-use this gasket when you put the filter back together unless you bought a new one when you bought the tube sheets. If you have not started yet or have not put the filter back together yet you can also ways got out and buy a tube sheet tank gasket.

Once you have removed the top tube sheet you can start to pull all of the fingers out of the lower tube sheet and put them into the new tube sheet. You will want to clean the fingers first also before putting them into the new tube sheet. Once you have removed all of the fingers from the cracked lower tube sheet you can now line up the holes in the rubber tube sheet gasket with the lower tube sheet and then re-bolt on the

Now that the fingers are in the new lower tube sheet and the tube sheets are bolted back together you can stick the bump shaft back through the top of the filter. Once the bump shaft is through the top of the filter you can re-insert the long bolt that goes through the bump handle that you removed when disassembling the filter.

If you now have the filter all together you can line up your discharge fitting with your pool hoses or pipes and re-bolt down the top of the filter to the tank. If you have an old Hayward EC series filter with multiple bolts in the top you will want to make sure to tighten them down evenly to prevent leaks.

How To Repair Hayward Perflex Leaking Bump Shaft Seal:

On the bump shaft on the Hayward Perflex you will see two different o-rings. These o-rings are made from rubber and stop the water from leaking through the bump shaft, From time to time these o-rings will have to be replaced. If you see water leaking from your bump shaft on your Perflex filter then you will need to replace your o-rings.

To replace the o-rings you will need to disconnect the pump handle and remove the bolts of the bellyband from the filter tank top. Once you have done so you will be able to remove the inner filter assembly out from the filter top. Now that the bump shaft is exposed you can remove the o-rings if they are still on the shaft. Sometimes the o-rings get so old they just fall off and go out the backwash line. If this is the case you will not have to worry about removing them.

Once the old o-rings are removed from the bump shaft you will want to grease up the shaft with some lubricant and then slide the new or-rings onto the shaft and into the grooves. There will be an upper and a lower groove in the shaft for the o-rings to sit into. Once they are sitting into place correctly you will want to grease them again and then slide the bump shaft back through the top of the filter and then reattach the bump handle to the shaft.

Now that the filter assembly is reconnected to the top of the filter tank you can bolt the top of the filter tank on to the bottom of the filter tank using your bolts or bellyband. Depending on how old your Hayward EC filter is will determine if you have a bellyband or a bolt pattern. The older Yellow Perflex tanks had a bolt pattern with many bolts. The newer Gray Perflex tanks now have a bellyband with just one bolt you will have to remove or tighten.

How To Replace A Leaking, Stuck Or Broken Backwash Valve:

The standard backwash valve on the Hayward Perflex is actually made by Hayward and can be replaced easily with a few minutes of your time and of course a new replacement Hayward Perflex Backwash valve is required. Before you can change the valve you will want to backwash your swimming pool filter and then drain it by leaving the backwash valve open until all of the water comes out. If you are working on an above ground swimming pool you will need to plug the swimming pool returns and skimmer or shut the filter isolation valves so that the pool water does not keep filling the filter.

Once the pool filter is back washed and drained you can remove the backwash valve by turning it counter clockwise. If you have a backwash line attached to the backwash valve you will want to remove that first. This may also require you to move the backwash fitting from the old valve. It will take 5 – 8 complete 360-degree spins or so before the valve becomes free. Once the valve is removed you will have to replace it with your new Hayward Perflex Backwash Valve.

You will now want to wrap the backwash valves threads with a few wraps of Teflon Tape before installing the valve. Once you have applied the Teflon tape you can tighten the new backwash line into place. If you had a backwash hose hooked up to the old valve you can now hook your backwash line on to your new backwash valve.

Now that the new backwash valve is installed you will want to put the valve in the off position and remove the plugs from the filter and the return jets if you were working on an above ground pool. You can now start your filter back up and re-add your D.E. powder. If you see any small drips or leaks from the new valve, shut off the filter and tighten the valve a bit more.

Hayward Perflex EC-Series Pool Filter Troubleshooting:

Problem: “My Perflex Pool Filter is leaking from the bump shaft”

Solution: You will have to replace the o-rings that are on the bump shaft. They are either worn or missing and this is why the shaft is leaking on your Hayward Perflex Filter.

Problem: “How Do I tell How Old My Perflex Filter Is?”

Solution: Hayward made the tanks on the EC-series Yellow for many years, so if you have a yellow tank you have an older filter. If your tank is gray you have a new Hayward Perflex Pool Filter.

Problem: “My backwash valve is still leaking after I have shut it off”

Solution: You can screw in a plug with an o-ring into the end of the backwash line as a temporary fix until you get a new backwash valve.

Problem: “How Do I bleed the air from my Perflex Filter?”

Solution: You can bleed the air our using the air relief screw on top of the filter.

Problem: “When I push my bump handle up and down it feels like its not working and really loose, what is wrong?”

Solution: When you push the bump handle up and down and it feelslike nothing is working it usually means that one of the c-clips that are connected to the bump shaft has broken and now the shaft can not push the tube sheets up and down. You will need to replace both the upper and lower bump shaft c-clips.

257 Comments

  1. new Pool Owner… Just starting my EC40 above ground filter.. Did everything according to manual and store clerk (closed today). Not getting ANY PSi… Skimmer bucket empties when we turn it on after priming… Any thoughts????

  2. When I turn on the filter/pump, the pressure goes up but the bump handle does not rise up. What might be wrong???

  3. Hey there would you mind letting me know which hosting company you’re using? I’ve loaded your blog in 3 different internet browsers and I must say this blog loads a lot faster then most. Can you recommend a good internet hosting provider at a fair price? Thanks a lot, I appreciate it!

  4. The belly band on my old hayward filter will not tighten down all the way. I believe the brass long nut is stripped. Replacement parts are not avavilable. Is slightly tighten ok? The other bolt is tight, (part # DEX2420J1

  5. I Have a Hayward 65 filter we put all our chemiclas in water is cloudy
    not sure if something is wrong with the filter we just put in a new rubber gasket in we hear a humming sould every once in a while. Just cant seem to get it clean what should the psi be?

  6. I have a EC 50 Above ground..the valve (SP 1480 BLK) has a tap drilled in it, for my chlorinator tube..I want to replace the valve….I cannot find it with a tap drilled in it….
    it has one male end and a female hexagon at the other end approx. 3- 4 inches in length… inside the female end it is curved (rounded) can you help?

  7. I just opened my pool…filter is 6 yrs old…had great flow ….primed still good….after about 1 hour…bump handle went limp…i could never move this when filter was running …now its flopping in the breeze….also lost all circulation and pressure…will a new bump shaft kit fix this ?

  8. I have a perflex ec65 filter/ super pump which is 5 yrs old. I have had problems for a week since opening. First what is proper bump psi, it starts at 15. I had an old gauge which had red an black arrows to give psi window, I put new gauge in, had pool guy come and clean grids. It started that I would loose suction when vac to bypass filter at opening. I backwashed and still losing suction. Went and bought new hose, same problem. shut it down 3 days till pool guy came to clean grids. No noticeable cracks or damage just very caked. I got new gauge because kept going to above red line within an hour, bumped and went down. But in years past it always remained at only below 17 and so I went to get new gauge thinking reading on gauge wrong. I feel like I am being held captive by having to be near my filter to bump alot. I am wondering how long these last? The pool guy did not seem to thrilled to keep answering ? on these troubleshooting scenarios. I so far got new hose, cleaned and inspected grid, got new gauge. Also, a small amount of product comes out after shut down about 5 seconds worth. Do I get pool clean and see what happens with system because maybe just real dirty? I use to run on timer but am afraid to.
    Thanks
    kathy

    • make sure all screws are TIGHT on filter along with connections, you might be getting air leaks, also backwash again-even if repair guy did it. -I use 6 lbs of DE -also we use a wand that you hook up to a garden hose -unscrew the pressure gauge and put it in the hole, it really does a good job of cleaning the fingers, i do this about every other backwash. If you pool is really dirty, you need to backwash often. Good Luck

  9. hi everyone, I feel like I’m missing something obvious, my De Hayward extended perflex filter is leaking inbetween the pieces that come together on the filter housing. i tightened the clamp, wiped everything down, looked at the gasket it has no viseable cracks but when i put it together ot leaks like a sive! mage sure everything was lined up to, is there some way to tell if that gasket is bad, and if i replace the gasket inbetween the plats can some one send me the steps?

    • I am having the same problem as a lot of the writers. My Hayward Perflex EC50C90 Series filter is leaking inbetween the two pieces that come together on the filter housing. I tightened the clamp, replaced the gasket, but when i put it together, it leaks like a sive! Made sure everything was lined up to. Took apart and together three times, but still leaks and not enough pressure to vacumn pool. Help

  10. my hayward ec50 leaks between the pieces that come together on the filter house. I have replaced the gasket twice, clwaned it and made sure evrything fits properly and it still leaks. What else can I do.

  11. i put my filter back together without placing the gasket between the plates an it works fine,does it work if you place gasket in tank an drop fingers down thru gasket cause im trying this next try or die my opinion seems like it will work handel s tight we will see!

  12. I have just replaced the Part Number 2 in your diagram. I have also replaced the gasket for good measure. I have also replaced the pump because I had low water flow. Since I have replaced the Part Number 2, the filter is spraying out water from between Part 2 and the filter housing. The gasket is seated properly and there is no crack in the new Part 2. I have take it off and checked and reassembled. Still on startup when building pressure, water sprays out, and then once pressure is equalized, goes away, them comes back to spray out when pressure builds. I have bled the air, but upon start up the basket was not fully filling with water so I had to open the top to faciliate that. no obstructions in line that I see. Water level in skimmer is perfect. Very frustrasted and out of $. Please advise. (Could dirty filter fingers cause this? I cleaned them with a hose, but not chemically.) Help!!!! :(

    • I have founds the problem Hairline crack in the filter body. : / Bought new (used) body and so far working fine. AMAZING how something that microscopic could suck air and ruin a day. lol

  13. I’ve been browsing online greater than three hours as of late, but I by no means discovered any attention-grabbing article like yours. It’s pretty worth sufficient for me. In my view, if all website owners and bloggers made excellent content as you did, the net will be a lot more useful than ever before.

  14. Right now it sounds like Expression Engine is the top blogging platform
    out there right now. (from what I’ve read) Is that what you’re using
    on your blog?

Leave a Reply to susan Cancel reply

Your email address will not be published.

This div height required for enabling the sticky sidebar
Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views :