Also Check Out: Join The Latest Discussions|Daily Updates| All Categories ||WeT Head Media Video||WeT Head Media Photos|
Latest Discussions
-
Topic: Weil McLain Ultra Series 2 Gas Fired Water Boiler Freshness: 17 hours 10 minutes ago Reply
Kirk wrote: Rich You seem to understand your boiler well enough I think I can lead you through this. 1) With the boiler display in standby (STBY) mode. 2) Press and hold the STEP button. While holding the STEP button press and hold the MODE button. Hold both buttons together for several seconds until CODE is displayed. Release buttons. CODE stays on the display. 3)NOTE: If CODE is not displayed after several seconds release the buttons and press MODE button several times to return to STBY. Repeat step 2 again. Once CODE is displayed: 4) Press STEP button once. 5) Use the + or – buttons to make the display show C-05. 6) Press the STORE button. 7) Press the...
Topic: Weil McLain Ultra Series 2 Gas Fired Water Boiler Freshness: 18 hours 29 minutes ago Reply
Rich wrote: I already have that set at 185F. I guess I could make it 190F but what I really am looking to do is shift the left side of the curve up so that at 55F or so I hit 120F. If I could do that I would then want to turn the boost off. Is that possible?
Topic: Top Five Oil Burner Troubleshooting Tips Freshness: 18 hours 37 minutes ago Reply
Robert Leitzel wrote: My oil burner will not start when I call it from the thermostat but it will fire when I hit the reset button. It also will not run for the whole cycle and warm the house to temp at that point I have to hit the reset button again. What’s Up?
Topic: Weil McLain Gold Series CGt Gas Fired Boiler with Tankless Heater Review Freshness: 1 day 0 hours ago Reply
joseph neigel wrote: I have a CGT5 that was installed in June 2009. The contractor was terrible. He built his business over 35 years ago and now let’s his kids run it. Say no more. You all know the rest. The system is wrong for my home. Aside being installed off the kitchen when the noise of the venting is terrible, it does not send hot water to the back rooms. I am now working with another contractor trying to resolve the problem Wish me luck. Lesson learned know your contractor’s reputation NOW not in the past. And call in other contractors to hear there story on their unit.
Topic: Bryant Evolution Series Heat Pump Review Freshness: 1 day 1 hour ago Reply
matt wrote: This message is for Barry or any other Bryant contractor. I want to install a bryant evolution 288ana036000 heatpump in my home. I have a newmac oil furnace. Can this be installed as an add on to my existing equipment? I am not ready to replace my furnace because it is brand new. It shows that it needs an evolution control to function properly and when I look at the wiring of the ABCD bus it shows the evolution control wired directly to the furnace than to the heat pump through that ABCD bus. Can these heat pumps work without the evolution control? Can I wire it to a 3 heat 2 cool heat pump stat?
Topic: Taco 006 Pump Circulating Pump Review Freshness: 1 day 14 hours ago Reply
David L. wrote: See http://floproteam.com/uploads/ FileLibrary/102-140.pdf That’s about as close as I’ve found on the web.
Topic: Weil McLain Ultra Series 2 Gas Fired Water Boiler Freshness: 1 day 15 hours ago Reply
Kirk wrote: Rich, Try raising your temperature setting for Parameter 4 (page 18 of the Control supplement). This is the setting that the water temp will operate when the outside temp is 32 or lower. It also changes the curve (Fig.5 page 10) to a steeper response in relation to lowering outdoor temperatures. Reply
Topic: Weil McLain Ultra Series 2 Gas Fired Water Boiler Freshness: 1 day 15 hours ago Reply
Kirk wrote: Rich, Try raising your temperature setting for Parameter 4 (page 18 of the Control supplement). This is the setting that the water temp will operate when the outside temp is 32 or lower. It also changes the curve (Fig.5 page 10) to a steeper response in relation to lowering outdoor temperatures.
Topic: Top Five Oil Burner Troubleshooting Tips Freshness: 1 day 21 hours ago Reply
Peter wrote: My boiler fires, then loses the flame. Each time this happens the exhaust vent opens and shuts. The boiler keeps doing this repeatedly. I have hit the emergency switch until I can get a repair tech over the house. What is the problem? Thank you.
Topic: Top Five Winter Swimming Pool Cover Care Tips Freshness: 1 day 21 hours ago Reply
William wrote: Nice article, a lot of common sence things though.
Topic: How To Troubleshoot A Beckett Oil Burner Freshness: 2 days 7 hours ago Reply
J.Thomas wrote: Is there any online stores where I can get the parts from for my beckett burner. I also want the “hand pump” to push/bleed the gunk from the oil lines. are nozzles generic as long as it meets number. Thanks.
Topic: Top Five Oil Burner Troubleshooting Tips Freshness: 2 days 12 hours ago Reply
steve treat wrote: On the motor non start up problem I forgot to mention the boiler is Weil-McLain and burner/motor is Carlin EZ pro EZ-1HPW motor model 98022.
Topic: Weil McLain Ultra Series 2 Gas Fired Water Boiler Freshness: 2 days 13 hours ago Reply
dave wrote: i have ran water through the boiler the way it should go. i hooked up a water hose where the pressure relief valve is on the supply side and ran water through the boiler and out of the drain valve on the bottom of the boiler so there is no flow problem through the boiler. i have 1″ copper pipes in and out of boiler and it ran just fine last year as i stated. i dont have any zone valves or flow valves anywhere. i have no clue why water will not flow through the boiler. i am going to call a local boiler tech see if he can figure it out
Topic: Top Five Oil Burner Troubleshooting Tips Freshness: 2 days 14 hours ago Reply
steve treat wrote: My motor is not starting on its own. Sometimes I have to cut power open up the electrode panel and reach in with a stick to spin the squirrel cage. When I turn power back on the motor spins an the burner fires and works. What is the problem?
Topic: How To Troubleshoot A Beckett Oil Burner Freshness: 2 days 16 hours ago Reply
Christian Melson wrote: To Matt: change the motor they usually fail if they go underwater.
Topic: Hayward Super Pump Repair Guide Freshness: 2 days 17 hours ago Reply
Joseph wrote: Mark, Here is the bearing that most people use from Grainger I think a guy on one of these comments said he went there and got both for like $18 ;-) He even reported back and said the pump now works great! http://www.grainger.com/Graing er/items/1ZGH5?Pid=search
Topic: Polaris Booster Pump Troubleshooting & Repair Guide Freshness: 2 days 17 hours ago Reply
Joseph wrote: Hi Alex, I usually take some silicon and spot it on the volute and then lay the o-ring into place and let it set for a few minutes. This way when you go to bolt the Polaris back together the gasket will not slip or move out of place. That is what usually makes the gasket leak or drip. You will also want to tighten the bolts just snug inn a star formation to ensure that the two pieces of the pump house bolt together evenly. Let me know if you have any more questions. Joseph
Topic: Hayward Super Pump Repair Guide Freshness: 2 days 17 hours ago Reply
Joseph wrote: Hi Mark, Sound like the bearings for sure. You can buy them from a local pool supply center that sells parts, or even a small motor shop. You could also buy them from grainger as well. You will need (2) / 6205 bearings most likely. The “6205″ is the bearing model # You can also buy the bearings online from grainger or another pool supply website, Here is the link to Grainger http://www.grainger.com/Graing er/wwg/search.shtml?searchQuer y=6205+motor+bearing&op=se arch&Ntt=6205+motor+bearin g&N=0&sst=All Grainger also has local store fronts as well. Here is a link to one online I just found searching quickly, you may want to shop around or...
Topic: Polaris Booster Pump Troubleshooting & Repair Guide Freshness: 2 days 17 hours ago Reply
alex wrote: What is the correct way to install the o ring on Polaris booster pump. I installed a new o ring and sealant and when started it leaked out front of pump. Checked tightness of 6 housing bolts, seemed tight. Thank you.
Topic: Hayward Super Pump Repair Guide Freshness: 2 days 19 hours ago Reply
Mark wrote: Joseph, I have a Hayward Super II 3/4 hp pool pump that has just started whining very loudly. I am assuming it is the bearings and am going to tackle replacing them. Do you know where I can get the bearings? I called Hayward and they said they don’t service the motors and to take it to a motor shop. Thanks, Mark
Topic: Weil McLain Ultra Series 2 Gas Fired Water Boiler Freshness: 2 days 21 hours ago Reply
Rich wrote: On the Ultra series 2 I dont see a way to set the miniumn target temp when using the outdoor reset. I checked through the control suppliment and see where you set the design temp and the target temp at the design temp but I dont see anywhere to set miniumn water temp. I am running Slantfin, thinfin baseboards and they really like 120 degrees or more. I find on warmer days it starts off with the target temp too low and it take about 30 minutes before target temp kicks up via the boost feature before the the room temp starts to rise. I use proliphix termostats monitored by intherma.com(highly recommend) and it is really easy for me to see the temp not...
Topic: Top Rated Water Heaters For Mobile Homes Freshness: 3 days 0 hours ago Reply
Gerri wrote: I am looking for a Mobile home water heater not gas and one that will be installed for my washing machine in my shed. I do not have a phone number that I can reach you at and I need help soon as possible to have a water heater installed in my home. Please email me with your email or Phone number so I can get a est.. On how much it will cost to have one put in and how much it will cost all together. I am a disabled woman and Of course the state doesnt help me to live on anything that is feesable in any conditions So please help me and email me as soon as You get this message and we can see what I can do to buy a water heater.. thank you for your time and I...
Topic: How To Fix Seven Types Of Leaky Faucets Freshness: 3 days 3 hours ago Reply
jody wrote: Why does my shower leak when I wash clothes? Jody
Topic: Best Automatic Swimming Pool Cleaners 2009 Freshness: 3 days 4 hours ago Reply
manohar wrote: hai this is manohar it was nice project… And i have an idea that can we make an automatic duster just clening the school board automatic when the teacher finishes the writing on board. and also can we operate through voice commands .. for example if i say clean the board so automatically it has to clean the neatly in fraction seconds, and halt means it has to halt.. so like wise can we make a project like this so, this will be helpful all sort of things like for teachers to professors. so please reply to my mail .. i will be waiting. well i am from india studying master of technology in power electronics in bangalore(karnataka). in oxford college....
Topic: How To Fix Seven Types Of Leaky Faucets Freshness: 3 days 14 hours ago Reply
Todd wrote: I replaced the seat and the entire cartridge in my leaking kitchen faucet, but I think that I over-tightened the cartridge when I was installing it. Now it is leaking from the base of the handle. What will I have to do to fix my mistake? Thanks.
Topic: How To Troubleshoot & Repair Swimming Pool Pumps Freshness: 4 days 13 hours ago Reply
Joseph wrote: Hi Please make sure the impeller somehow did not get jammed with debris.
Topic: Kohler Antique Series Bathroom Faucets Review Freshness: 4 days 13 hours ago Reply
Joseph wrote: Hi, What information are you looking for?
Topic: How To Troubleshoot & Repair Swimming Pool Pumps Freshness: 4 days 14 hours ago Reply
Sandy wrote: We replaced the capisitor on the pool pump and it started up fine but when I turned it off to back wash and tried to turn it back on it tripped the breaker and will not come back on. Any suggestions? Please help!
Topic: Kohler Antique Series Bathroom Faucets Review Freshness: 4 days 14 hours ago Reply
Ted Czupka wrote: Replacing (2) 1992 installed Polished Brass wide-spread lav. faucets that look like K9656 style except the lift rod is under the faucet spout. Please reply, thank you!
Topic: How To Troubleshoot A Beckett Oil Burner Freshness: 4 days 15 hours ago Reply
Matt wrote: I had a sewage backup and the burner was partially under water.After pumping out the water I tested the burner and it fired. After sitting and drying overnight it will not fire. It humms but I don’t hear anything else. Then it trips. It sounds like the pump is not pumping oil and the electrodes are not firing. Any advice?
Recent Trackbacks:
- Rinnai R50LSi Tankless Water Heater Review: With the R50LSi you are getting a tankless water heater that is rated...
- Baquacil Vs Chlorine: that claim to be the best but there are two great systems that can live up to that claim, the...
- Top Flushing Toilet Awards 2009: Gerber Avalanche Super Toilet is the newest toilet in the Gerber Inventory. This...
- Little Giant Submersible Pump Buyers Guide: Little Giant 9S-CIM Sewage Ejector Pump is perfectly designed to help...
- Best Oil Fired Boilers 2009: Buderus G215 Oil Fired Residential Boiler is insulated with a 3″ thick thermal...
